{"id":3715,"date":"2026-11-19T17:38:54","date_gmt":"2026-11-19T09:38:54","guid":{"rendered":"http:\/\/www.germanarangopalau.com\/blog\/?p=3715"},"modified":"2026-11-19T17:38:54","modified_gmt":"2026-11-19T09:38:54","slug":"can-gpo-3-be-cut-with-a-waterjet-44ac-e7f37b","status":"publish","type":"post","link":"http:\/\/www.germanarangopalau.com\/blog\/2026\/11\/19\/can-gpo-3-be-cut-with-a-waterjet-44ac-e7f37b\/","title":{"rendered":"Can GPO-3 be cut with a waterjet?"},"content":{"rendered":"<p>If you\u2019re a spec engineer, fabrication shop owner, or someone who works with electrical insulation materials, you\u2019ve probably asked yourself this question at some point: <em>Can GPO-3 be cut with a waterjet?<\/em> As a GPO-3 supplier who\u2019s fielded this exact query from dozens of customers over the years, I get why it\u2019s such a common one. GPO-3 is super tough stuff\u2014laminated fiberglass-reinforced polyester, rated for high heat and electrical stress, used in everything from transformer switchboards to industrial control panels. It\u2019s not like cutting soft plywood, so picking the right method matters a lot. No one wants a warped part, a frayed edge, or something that doesn\u2019t meet electrical safety standards. <a href=\"https:\/\/www.nova-insulation.com\/gpo-3\/\">GPO-3<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.nova-insulation.com\/uploads\/20209814\/small\/pmma-and-ptfe-engineering-plastic27489751637.jpg\"><\/p>\n<p>Let\u2019s cut to the chase first: yes, you <em>can<\/em> cut GPO-3 with a waterjet, but there\u2019s a right way and a very wrong way to do it. A lot of guys I work with have tried winging it, and that\u2019s where problems pop up. Let\u2019s break down why waterjet is even a contender here, what makes GPO-3 unique, and the mistakes to avoid if you\u2019re planning to use this method.<\/p>\n<p>First, let\u2019s refresh what GPO-3 is, just to make sure we\u2019re all on the same page. It\u2019s a thermoset composite, right? Made by compressing layers of fiberglass mat with a polyester resin binder under high heat and pressure. That combination gives it insane dimensional stability, high arc resistance, and a heat deflection temperature around 300\u00b0F (149\u00b0C)\u2014way higher than regular fiberglass or even many plastics. But that rigidity also means it\u2019s prone to chipping or delaminating if you use a cutting method that\u2019s too harsh, like a standard saw blade. A router or band saw can work, but they leave rough edges that need finishing, and the heat from the blade can actually break down the resin, ruining the insulation properties right at the cut.<\/p>\n<p>So why waterjet? It\u2019s a cold-cutting method, right? No heat-affected zone (HAZ) to speak of. The water mixed with abrasive (usually garnet) slams into the material at high speed, eroding it away cleanly. For composites, that\u2019s a big deal. Unlike a saw that can split the fiberglass layers or fray the resin, a waterjet cuts through GPO-3 smoothly, with almost no burr. I\u2019ve had a few customers switch from band saws to waterjets and tell me they cut their finishing time in half. That\u2019s a win for anyone on a tight production schedule.<\/p>\n<p>But here\u2019s the catch: it\u2019s not as simple as firing up any old abrasive waterjet and cutting GPO-3 at full speed. If you mess up the parameters, you\u2019ll end up with something that\u2019s not usable. Let\u2019s talk about what goes into a good waterjet cut for GPO-3. First, the abrasive size. Most guys use 80-mesh garnet for general metal cutting, but GPO-3 is softer than steel. If you use too fine an abrasive (like 120-mesh), you\u2019ll get a slow, uneven cut that can delaminate the fiberglass layers. Too coarse (50-mesh), and you\u2019ll leave a super rough edge that still needs sanding. What\u2019s the sweet spot? From all the tests our customers have run, 70-to-80-mesh garnet works best. It\u2019s aggressive enough to cut through the fiberglass mat cleanly, but not so rough that it tears the resin.<\/p>\n<p>Then there\u2019s the pressure. Abrasive waterjets usually run between 40,000 and 60,000 PSI. For thin GPO-3 (like 1\/8-inch, used for small insulators), 40,000 PSI is enough. For thicker stuff\u2014say 1-inch GPO-3, which is common for switchgear bases\u2014you\u2019ll want to bump it up to 50,000 PSI. Run anything lower than that, and the jet won\u2019t have enough force to cut all the way through without dragging, which causes edge damage. Too high, and you\u2019ll etch the surface of the GPO-3 or cause micro-delamination deep in the part, which no one can see but will fail electrical tests down the line. Oh, and speed matters too. Slow down for thick material, speed up for thin. If you\u2019re cutting a 1\/4-inch sheet at 2 inches per minute, that\u2019s too slow\u2014you\u2019ll over-abrade the edge. Run it at 10 inches per minute, and that\u2019s about right for 70-mesh garnet at 45,000 PSI.<\/p>\n<p>Wait, let\u2019s talk about a common mistake I see all the time: not securing the GPO-3 properly. Waterjets can cause thin or flimsy material to vibrate mid-cut, which leads to wavy edges or even parts that shift. GPO-3 is rigid, but if you\u2019re cutting a small, 1\/8-inch thick bracket, it\u2019ll still move if it\u2019s not clamped down tight. Use a vacuum hold-down or multiple clamps along the edges. And don\u2019t over-clamp the part\u2014you don\u2019t want to warp the GPO-3 before you even start cutting.<\/p>\n<p>Another thing: scrap. GPO-3 isn\u2019t cheap, and waterjet cutting does create some kerf (the width of the cut) waste. For most standard cuts, the kerf is around 0.03 inches. That means if you\u2019re nesting a bunch of small parts on a sheet, you need to leave at least 0.04 inches between each part to avoid cutting into them. It\u2019s not a big deal, but it\u2019s something to factor in if you\u2019re trying to minimize scrap for big runs.<\/p>\n<p>Now, let\u2019s address the elephant in the room: is waterjet cutting up to electrical insulation standards? Because that\u2019s non-negotiable for GPO-3. The last thing you want is a cut part that fails a high-voltage test because of edge damage. I\u2019ve worked with testing labs that have verified waterjet-cut GPO-3 meets the same ASTM D7032 specs (that\u2019s the standard for GPO-3) as parts cut with router methods, as long as you follow the right parameters. The cold cut means no HAZ, so the resin structure stays intact. That\u2019s way better than a saw cut, which can have a 0.01-inch HAZ where the resin is degraded, leading to lower arc resistance.<\/p>\n<p>But wait\u2014what if you\u2019re cutting really thick GPO-3, like 2 inches? I\u2019ve had a customer try that, and he almost messed up his first cut by going too slow. The problem with thick material is that the abrasive has to penetrate all those fiberglass layers, so if your speed is off, you\u2019ll get a taper on the edges of the cut. A slight taper is normal, but if it\u2019s more than 1 degree, that part won\u2019t fit in the assembly. The fix? Use a slightly higher abrasive flow rate\u2014like 1.5 pounds per minute instead of 1 pound\u2014to keep the jet focused through the thickness. And do a test cut on a scrap piece first. I can\u2019t stress that enough. For any custom job, always test your parameters on a scrap sheet before cutting your production parts. It saves you from wasting a whole sheet of GPO-3 when you tweak the speed by 10 inches per minute.<\/p>\n<p>Now, let\u2019s talk about when waterjet <em>isn\u2019t<\/em> the best choice. If you\u2019re cutting really small, intricate parts\u2014like tiny insulators with complex shapes\u2014a router or laser might be cheaper for low runs, but wait, no\u2014lasers actually don\u2019t work great for GPO-3. The heat from a laser causes the resin to burn, leaving a charred edge that\u2019s bad for insulation. Routers work, but they require more finishing. For medium to large runs of custom GPO-3 parts, waterjet is actually one of the most efficient methods. And if you\u2019re dealing with thick stock (1\/2 inch or more), waterjet beats most other methods hands down.<\/p>\n<p>I remember a few months back, a fabrication engineer came to me frustrated. He\u2019d tried cutting 1-inch GPO-3 with a band saw, and every part had a rough edge that he had to sand for 10 minutes each. He switched to a waterjet shop near him, but he didn\u2019t tell them what GPO-3 was, so they used 50-mesh garnet and cut it too slow. The edges were so rough that half the parts failed their QC check. He brought those bad parts to me, and I explained what went wrong. We sent him a set of test scrap, and he dialed in the parameters with the waterjet shop: 70-mesh garnet, 48,000 PSI, speed adjusted for thickness. After that, his scrap rate dropped from 20% to almost zero, and his finishing time was cut in half. That\u2019s the kind of win we like to see.<\/p>\n<p>Another point: material quality. Not all GPO-3 is the same, and that affects how it cuts. Lower-grade GPO-3 has inconsistent resin distribution, which can cause delamination during waterjet cutting. That\u2019s why buying from a reputable supplier matters. We test every batch of GPO-3 we carry for resin content and fiberglass uniformity, so our customers don\u2019t run into issues mid-cut. If you\u2019re working with cheap off-brand GPO-3, even the best waterjet parameters won\u2019t save you from bad cuts.<\/p>\n<p>Let\u2019s wrap this up so it\u2019s not just a bunch of tech specs. To answer the original question: Yes, GPO-3 can absolutely be cut with a waterjet, <em>when done correctly<\/em>. The key parameters are 70-to-80-mesh garnet abrasive, 40,000 to 50,000 PSI depending on thickness, proper cutting speed, and good part clamping. It\u2019s a cold, clean method that avoids the heat damage of saws or routers, leaves smooth edges that meet electrical standards, and saves time on finishing.<\/p>\n<p>But if you\u2019re still unsure, or you have a custom job that needs GPO-3 cut right, don\u2019t guess. A little misstep here can lead to wasted material, bad parts, and delayed orders. I\u2019ve been in this industry for years, and I\u2019ve seen enough guys mess up because they tried to cut corners on parameters. So if you\u2019re planning a waterjet cut for GPO-3, or you want to make sure your custom parts are up to spec, don\u2019t hesitate to reach out. We can walk through your project, share the parameters that work for your thickness and part shape, and even send you test scrap if you want to try it out first. No sales pitch, just straight-up advice from someone who\u2019s worked with GPO-3 every day.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.nova-insulation.com\/\"><\/p>\n<p>When you\u2019re dealing with electrical insulation, you can\u2019t afford to cut corners. And when it comes to cutting GPO-3, a little know-how goes a long way. So if you have questions, or you\u2019re ready to order GPO-3 stock and talk through your cutting plan, hit me up. We\u2019ll make sure you get parts that fit, work, and meet all the safety standards you need.<\/p>\n<p><a href=\"https:\/\/www.nova-insulation.com\/cnc-machined-parts\/epoxy-glass-gasket\/\">Epoxy Glass Gasket<\/a> References<br \/>\nASTM D7032 \/ D7032M-17, Standard Specification for Glass-Matrix Polyester Laminate (GPO-3) for Electrical Insulation.<br \/>\nWaterjet Cutting Parameters for Composite Materials, Abrasive Waterjet Manufacturers Association (AWJA) Technical Bulletin 2021-04.<br \/>\nThermoset Composite Cutting Methods: Comparative Analysis of Edge Quality and Insulation Performance, Journal of Electrical Materials and Manufacturing, 2020.<\/p>\n<hr>\n<p><a href=\"https:\/\/www.nova-insulation.com\/\">Nova Insulation Material Co., Ltd.<\/a><br \/>Nova Insulation Material Co., Ltd. is one of the most professional gpo-3 manufacturers and suppliers in China, featured by quality products with competitive price. Please rest assured to wholesale gpo-3 made in China here from our factory. Also, quotation is available.<br \/>Address: Rm 1711, Block B, iPark Bldg. Deng Liang Rd. Nanshan, Shenzhen, GD 518054 China<br \/>E-mail: sales@nova-insulation.com<br \/>WebSite: <a href=\"https:\/\/www.nova-insulation.com\/\">https:\/\/www.nova-insulation.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>If you\u2019re a spec engineer, fabrication shop owner, or someone who works with electrical insulation materials, &hellip; <a title=\"Can GPO-3 be cut with a waterjet?\" class=\"hm-read-more\" href=\"http:\/\/www.germanarangopalau.com\/blog\/2026\/11\/19\/can-gpo-3-be-cut-with-a-waterjet-44ac-e7f37b\/\"><span class=\"screen-reader-text\">Can GPO-3 be cut with a waterjet?<\/span>Read more<\/a><\/p>\n","protected":false},"author":417,"featured_media":3715,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3678],"class_list":["post-3715","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-gpo-3-431b-e829e7"],"_links":{"self":[{"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/posts\/3715","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/users\/417"}],"replies":[{"embeddable":true,"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/comments?post=3715"}],"version-history":[{"count":0,"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/posts\/3715\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/posts\/3715"}],"wp:attachment":[{"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/media?parent=3715"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/categories?post=3715"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.germanarangopalau.com\/blog\/wp-json\/wp\/v2\/tags?post=3715"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}